Openatv 3.5 for the zgemma H2.H with Kiddacs VSkin HD with slyk1hd set it as your skin
And mgcamd1.38 and cccam2.30 with setup guide
this backup has been set to generate one set of bouquets by replacing the non available
sky hd channels with vm hd channels so the channel numbers will be the same as sky 106 sky 1hd and 107 is sky living hd
09/08/2016
PLEASE NOTE YOU WILL NEED BOTH VM AND SKY ACTIVE TUNERS AND SUB FOR THIS BACKUP TO WORK
Set with mgcamd1.38. & cccam2.3 and with all mg_cfg and newcamd.list and CCcam.cfg files needed in place! Just edit your details in and reboot! DO NOT SEND YOUR FILES IN. EDIT WHATS ALREADY THERE
OK. Basically u need a usb or hard drive that can be wiped and devoted to the box.
That will store program guide and recordings and timeshift to rewind TV etc.
4gb is minimum I'd recommend. But more is better.
Once image is flashed and u edit ur newcamd.list file in usr/keys or CCcam.cfg in usr/keys with FileZilla.
Get the permanent USB/hdd onto a PC and quick format it.
download here :download:
Tlashing the box
flash with the zgemma folder only on a formatted usb stick turn of box using back power button insert usb in back and switch on using back button then box should change from usb to flash.
ZGEMMA DISHCABLE'S SETTUP
Plug one dish cable into tuner A(sat). And the second cable into B(vm).
You will need to blug kenable F Type Screw Connector Socket to RF Coax Aerial Male Adapter to plug into tuner b
rf adapter.jpg
Then
Menu, setup, service searching, Tuner configuration,
Select Tuner B: and input your network id
tuner configuration.jpg
Check here for a list of network ids http://www.techkings.org/general-cab...le-netids.html
Please note you will need both sky and cables tuners and subs for this image to
Work
h2h setup.jpg
added info: you will also need a network connection for scanning channels and to unscramble the channels
either use a lan cable, home plugs or wifi adapter. lan cable or home plugs is recommended for a more stable connection
please do not post in this thread regarding wifi adapters as i dont use them so i cannot offer support
USB/ HARD DRIVE SETUP
Box off.
Usb in rear.
Box on.
Blue Button
Harddisk/Harddisk Setup press right
initialisation.jpg
Initialization choose your device and press red to initialise
then convert ext3 to 4 choose your device and press red to convert ext3 to 4
convert ext3 to 4.jpg
Creating Swapfile
I dont think the newer models need a swapfile but if you want to
MENU, Infopanel, Plugins, SwapManager, GREEN, Select your drive, 256Mb, takes a couple of mins to create, once created choose RED to activate and YELLOW to autostart
swap manger.jpg
restart box not GUI
Recording and Timeshift settings
Menu
Setup
System
Recording and Timshift settings
Recording settings
Default movie location should be media/hdd/movie
recording settings.jpg
(If u are using a large enough usb/HDD u may want to go to
Menu
Setup
System
Rexording and timshift settings
Timeshift settings
Ensure timeshift location is showing: media/hdd/movie/timesshift
Autorecord is showing media/hdd/movie
if you want enable Autorecord
Autostart ts after 30secs or whatever.
As it is u must press pause to start timeshift)
timeshift settings.jpg
If you find that the screen is to large/small/off to side:
Menu
Setup
Usage and GUI
Extended GUI
OSD Position
U can change about here. Including transparency of windows.
Running the sat_282_uk_CustomMix.xml updater
Before setting up abm we need to run the sat_282_uk_CustomMix.xml updater plugin
Press portal at the bottom click on the sat_282_uk_CustomMix.xml updater plugin you will have a message saying file downloaded press exit.
custommix updater.jpg
This will ensure your using the latest custommix.xml file to swap the sky hd channels with vm and to add channel numbers on epg
TO SETUP ABM
Menu
Setup
Service searching
Autobouquets maker
Providers. Wait
Sky UK: area. Change from northwest Yorkshire HD to your area HD not sd or custom we need HD to swap with cable by pressing right or left.
You may want to go down and change sky uk channel swap to no if you don’t have bbc1hd and ITV hd versions in your are in.
abm sat.jpg
Then virgin(uk): area change 41064 York(ff Leeds) to your net id
abm vm.jpg
No need to generate other bouquets
Green to save.
Start scan. Wait.
Exit all
Hold power Restart
TO SETUP EPG
I have set-up crossepg for sat and epgrefresh for cable
For crossepg (sat)
Menu
Setup
Cross EPG
Download now. Takes 5-10 mins. Will seem like its stuck on Loading Data. Wait.
Happens automatically at 6.00 am anyway.
Exit all
crossepg.jpg
Hold power again and restart.
For epgrefresh(cable)
Go to all channels bouquet select the vm previews channel and press the green button then epg refresh now
epg refresh.jpg
this is setup to automatically run at 5.30 am.
This is also set to shut down the box after automatic scan at 5am if you want to change this portal, epgrefresh show advance options yes
Change shutdown after EPG refresh to no.
Kiddacs vskin v1.011
Kiddacs slyk1hd v4.009
auto bouquets setup
Auto epg update set
Cross epg setup to hdd
Includes mgcamd, cccam, openwebif, picture player, Media scanner, Dream-Explorer, Iptv Player, epg refresh and cachflush
custommix updater
the latest sat_282_sky_uk_CustomMix.xml is downloaded every time you run the sat_282_uk_CustomMix.xml updater thanks to wooshman for the great help
To install picons if you want
you will need to download srp picons because snp picons will not work
Picons are the little channels logos you see on some screen shots and these instructions guide you through adding them to your EPG and info bars.
First of all check that you have no previous picons installed and if so remove them
From full screen TV:
Press the Portal button -> Red button (remove plugins) -> Highlight +Picons and press OK
Now any picon lists you see in that section need removing. Highlight, press ok and select yes.
Once you have removed any existing picon sets exit right back to full screen TV.
From full screen TV:
Press the Portal button -> Green button to download plugins -> Highlight +feeds and press OK -> Highlight picons.xyz and press OK -> Press OK again
Once you are returned to the list of plugings Press Exit once (the box may appear to hang) press Exit again, Press and hold Standby button and select Restart to restart the box.
When your box has restarted:
Press the Portal button -> Green button to download plugins -> Highlight +picons -> Press the OK button
Scroll right down the list and highlight: srp-full.400x240-370x210.light.on.transparent Press OK, Press OK again. Highlight and Select your external USB device
This takes a little while to download and extract due to there being 7000+ picons and may appear to have crashed. How long it takes will also depend on the speed of your USB device. While you are waiting be patient wait and wait some more.
When you are returned to the menu, Press the Exit button twice to return to full screen TV
Now press your EPG button and in the top left hand corner your should see the channel logo. It will also show up when you press the OK button from full screen TV
Changing the resolution of the box
This backup was made using the resolution for 720 tvs
To change this menu. setup, video, basic settings
go to mode and press right to change from 720 to what your tv supports
video settings.jpg
Idiots Guide for adding your line with Filezilla
On your Box Menu > Info> Network > Get your box IP address
Open up FileZilla Host (top left ) Type in IP address Username root Leave others blank Press Quick connect
Box should then connect to computer Left side computer, Right hand box
filezilla connect.jpg
For Nlines
On right hand side locate usr Double click it Then Keys Double click It You should now see 3 files CCcam.cfg, Mg_cfg and Newcamd.list On Newcamd list Left click/right click Then click View/Edit (It may ask you what program you wish to view the file choose Notepad) You will see 2 samples of what your line should look like either edit your line details or Delete up to CWS = (space either side of =)
Copy and past your line Less the N: in its place
Disconnect from FileZilla By Clicking the X just under bookmarks top of page
Press blue button on remote control >.Softcam press right Select soft cam panel Mgcamd 1.38 should show as default press green to restart
For Clines
Again usr/keys on box Your line goes Complete with the C in CCcam.cfg and start in Softcam panel press right to change cam
Hope it helps
This also has slyk1hd v4.009 to change it menu, setup, useage and GUI, Skin Setup and select slyk1hd
Check here for the latest V Skin HD http://www.techkings.org/zgemma-star...-vskin-hd.html
Check here for the latest slyk1 hd skin http://www.techkings.org/zgemma-star...available.html
Screen shots below enjoy
info.jpg
epg.jpg
channel select.jpg
plugins.jpg
And mgcamd1.38 and cccam2.30 with setup guide
this backup has been set to generate one set of bouquets by replacing the non available
sky hd channels with vm hd channels so the channel numbers will be the same as sky 106 sky 1hd and 107 is sky living hd
09/08/2016
PLEASE NOTE YOU WILL NEED BOTH VM AND SKY ACTIVE TUNERS AND SUB FOR THIS BACKUP TO WORK
Set with mgcamd1.38. & cccam2.3 and with all mg_cfg and newcamd.list and CCcam.cfg files needed in place! Just edit your details in and reboot! DO NOT SEND YOUR FILES IN. EDIT WHATS ALREADY THERE
OK. Basically u need a usb or hard drive that can be wiped and devoted to the box.
That will store program guide and recordings and timeshift to rewind TV etc.
4gb is minimum I'd recommend. But more is better.
Once image is flashed and u edit ur newcamd.list file in usr/keys or CCcam.cfg in usr/keys with FileZilla.
Get the permanent USB/hdd onto a PC and quick format it.
download here :download:
Tlashing the box
flash with the zgemma folder only on a formatted usb stick turn of box using back power button insert usb in back and switch on using back button then box should change from usb to flash.
ZGEMMA DISHCABLE'S SETTUP
Plug one dish cable into tuner A(sat). And the second cable into B(vm).
You will need to blug kenable F Type Screw Connector Socket to RF Coax Aerial Male Adapter to plug into tuner b
rf adapter.jpg
Then
Menu, setup, service searching, Tuner configuration,
Select Tuner B: and input your network id
tuner configuration.jpg
Check here for a list of network ids http://www.techkings.org/general-cab...le-netids.html
Please note you will need both sky and cables tuners and subs for this image to
Work
h2h setup.jpg
added info: you will also need a network connection for scanning channels and to unscramble the channels
either use a lan cable, home plugs or wifi adapter. lan cable or home plugs is recommended for a more stable connection
please do not post in this thread regarding wifi adapters as i dont use them so i cannot offer support
USB/ HARD DRIVE SETUP
Box off.
Usb in rear.
Box on.
Blue Button
Harddisk/Harddisk Setup press right
initialisation.jpg
Initialization choose your device and press red to initialise
then convert ext3 to 4 choose your device and press red to convert ext3 to 4
convert ext3 to 4.jpg
Creating Swapfile
I dont think the newer models need a swapfile but if you want to
MENU, Infopanel, Plugins, SwapManager, GREEN, Select your drive, 256Mb, takes a couple of mins to create, once created choose RED to activate and YELLOW to autostart
swap manger.jpg
restart box not GUI
Recording and Timeshift settings
Menu
Setup
System
Recording and Timshift settings
Recording settings
Default movie location should be media/hdd/movie
recording settings.jpg
(If u are using a large enough usb/HDD u may want to go to
Menu
Setup
System
Rexording and timshift settings
Timeshift settings
Ensure timeshift location is showing: media/hdd/movie/timesshift
Autorecord is showing media/hdd/movie
if you want enable Autorecord
Autostart ts after 30secs or whatever.
As it is u must press pause to start timeshift)
timeshift settings.jpg
If you find that the screen is to large/small/off to side:
Menu
Setup
Usage and GUI
Extended GUI
OSD Position
U can change about here. Including transparency of windows.
Running the sat_282_uk_CustomMix.xml updater
Before setting up abm we need to run the sat_282_uk_CustomMix.xml updater plugin
Press portal at the bottom click on the sat_282_uk_CustomMix.xml updater plugin you will have a message saying file downloaded press exit.
custommix updater.jpg
This will ensure your using the latest custommix.xml file to swap the sky hd channels with vm and to add channel numbers on epg
TO SETUP ABM
Menu
Setup
Service searching
Autobouquets maker
Providers. Wait
Sky UK: area. Change from northwest Yorkshire HD to your area HD not sd or custom we need HD to swap with cable by pressing right or left.
You may want to go down and change sky uk channel swap to no if you don’t have bbc1hd and ITV hd versions in your are in.
abm sat.jpg
Then virgin(uk): area change 41064 York(ff Leeds) to your net id
abm vm.jpg
No need to generate other bouquets
Green to save.
Start scan. Wait.
Exit all
Hold power Restart
TO SETUP EPG
I have set-up crossepg for sat and epgrefresh for cable
For crossepg (sat)
Menu
Setup
Cross EPG
Download now. Takes 5-10 mins. Will seem like its stuck on Loading Data. Wait.
Happens automatically at 6.00 am anyway.
Exit all
crossepg.jpg
Hold power again and restart.
For epgrefresh(cable)
Go to all channels bouquet select the vm previews channel and press the green button then epg refresh now
epg refresh.jpg
this is setup to automatically run at 5.30 am.
This is also set to shut down the box after automatic scan at 5am if you want to change this portal, epgrefresh show advance options yes
Change shutdown after EPG refresh to no.
Kiddacs vskin v1.011
Kiddacs slyk1hd v4.009
auto bouquets setup
Auto epg update set
Cross epg setup to hdd
Includes mgcamd, cccam, openwebif, picture player, Media scanner, Dream-Explorer, Iptv Player, epg refresh and cachflush
custommix updater
the latest sat_282_sky_uk_CustomMix.xml is downloaded every time you run the sat_282_uk_CustomMix.xml updater thanks to wooshman for the great help
To install picons if you want
you will need to download srp picons because snp picons will not work
Picons are the little channels logos you see on some screen shots and these instructions guide you through adding them to your EPG and info bars.
First of all check that you have no previous picons installed and if so remove them
From full screen TV:
Press the Portal button -> Red button (remove plugins) -> Highlight +Picons and press OK
Now any picon lists you see in that section need removing. Highlight, press ok and select yes.
Once you have removed any existing picon sets exit right back to full screen TV.
From full screen TV:
Press the Portal button -> Green button to download plugins -> Highlight +feeds and press OK -> Highlight picons.xyz and press OK -> Press OK again
Once you are returned to the list of plugings Press Exit once (the box may appear to hang) press Exit again, Press and hold Standby button and select Restart to restart the box.
When your box has restarted:
Press the Portal button -> Green button to download plugins -> Highlight +picons -> Press the OK button
Scroll right down the list and highlight: srp-full.400x240-370x210.light.on.transparent Press OK, Press OK again. Highlight and Select your external USB device
This takes a little while to download and extract due to there being 7000+ picons and may appear to have crashed. How long it takes will also depend on the speed of your USB device. While you are waiting be patient wait and wait some more.
When you are returned to the menu, Press the Exit button twice to return to full screen TV
Now press your EPG button and in the top left hand corner your should see the channel logo. It will also show up when you press the OK button from full screen TV
Changing the resolution of the box
This backup was made using the resolution for 720 tvs
To change this menu. setup, video, basic settings
go to mode and press right to change from 720 to what your tv supports
video settings.jpg
Idiots Guide for adding your line with Filezilla
On your Box Menu > Info> Network > Get your box IP address
Open up FileZilla Host (top left ) Type in IP address Username root Leave others blank Press Quick connect
Box should then connect to computer Left side computer, Right hand box
filezilla connect.jpg
For Nlines
On right hand side locate usr Double click it Then Keys Double click It You should now see 3 files CCcam.cfg, Mg_cfg and Newcamd.list On Newcamd list Left click/right click Then click View/Edit (It may ask you what program you wish to view the file choose Notepad) You will see 2 samples of what your line should look like either edit your line details or Delete up to CWS = (space either side of =)
Copy and past your line Less the N: in its place
Disconnect from FileZilla By Clicking the X just under bookmarks top of page
Press blue button on remote control >.Softcam press right Select soft cam panel Mgcamd 1.38 should show as default press green to restart
For Clines
Again usr/keys on box Your line goes Complete with the C in CCcam.cfg and start in Softcam panel press right to change cam
Hope it helps
This also has slyk1hd v4.009 to change it menu, setup, useage and GUI, Skin Setup and select slyk1hd
Check here for the latest V Skin HD http://www.techkings.org/zgemma-star...-vskin-hd.html
Check here for the latest slyk1 hd skin http://www.techkings.org/zgemma-star...available.html
Screen shots below enjoy
info.jpg
epg.jpg
channel select.jpg
plugins.jpg